更好保持打膠機性能穩定持久就要正確操作
一般情況下,能夠正確的使用機器，一方面能夠做好產品，另一方面也可以延長機器的使用壽命，保持機器的性能穩定持久。使用打膠機也是如此，下面簡單的說明一下。
In general, being able to use the machine correctly, on the one hand, can make the product well, on the other hand, it can also prolong the service life of the machine and maintain the stability and durability of the machine. The same is true when using the glue applicator. The following is a brief description.
使用機器前，確保電源電壓的穩定以及電路，保證機器在開機中正常運行。確保機器的各工件都處入原點位置，機器上沒有雜物，以免阻擋機器運行，經常給機器的滑輪處加黃油，保證門窗打膠機的滑輪潤滑，運轉時更流暢，機器正在工作時，看看周圍的人是否在的距離，以免機器在工作時傷害到旁邊的人。
Before using the machine, ensure the stability of the power supply voltage and the safety of the circuit, and ensure the normal operation of the machine during startup. Make sure that all the workpieces of the machine are at the origin position, and there are no sundries on the machine, so as not to block the operation of the machine. Often add butter to the pulley of the machine to ensure that the pulley of the door and window gluing machine is lubricated and runs more smoothly. When the machine is working, check whether the people around it are at a safe distance, so as not to hurt the people next to it when the machine is working.
由于雙組份密封膠的固化需要一定時間，因此，已打了雙組份密封膠的玻璃應水平輕輕搬動。A組、B組份膠應保持清潔，嚴防異物進入膠中。在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直單一的A組份膠從槍口排出為止。高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
Since the curing of two-component sealant takes a certain time, the glass with two-component sealant should be moved horizontally and gently. The glue of group A and B shall be kept clean to prevent foreign matters from entering the glue. In the continuous working process, the working time of the glue gun shall not exceed 20 minutes each time. Otherwise, all the mixed glue shall be washed out with component a glue until a single component a glue is discharged from the muzzle of the gun. The high-pressure rubber hose shall not be forcibly squeezed or bent to prevent affecting the normal operation of the system.
混膠器應經常保持暢通，以保證良好的出膠效果。如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
The mixer should always be kept unblocked to ensure good glue output effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to clean every 5 groups. When the glue gun is not used for a long time (more than a week), remove the gun body and clean the residual colloid in the glue gun and mixer with solvent.
不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每兩組清洗一次。任何因膠體固化所造成的膠槍、管路或整機的故障，一律不在保修范圍之內。定期給各泵的加油口加油，應保證油霧器內不斷油。
The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and one-way check valve of component B are clear. It is recommended to clean every two groups. Any failure of glue gun, pipeline or whole machine caused by colloid solidification is not within the scope of warranty. Fill the oil filler of each pump regularly, and ensure that there is continuous oil in the oil atomizer.
We should pay attention to some problems and maintenance methods when using Jinan two-component glue applicator at ordinary times. Don't use it blindly and violently, otherwise it is easy to cause damage to the equipment. The above is the relevant information. I hope you can help me. Please come to our website for more information http://sunflowder5188.com.cn Understand!
上一篇：雙組份打膠機的日常維護原來也分等級
下一篇：關于打膠機形成構思和工作原理
